![]() That’s how easy it is to change a bulb in your Ford’s front lights. TOP TIP: If you’re uncertain about your headlight alignment, your Ford Dealer will check it for you.Carefully align the headlamp with the bodywork.Push the main connector back in until it clicks. ![]() To put the lighting unit back in, reposition the headlamp unit.Put the new bulb into the electrical connector and put it back in the main unit.Twist the electrical connector anti-clockwise.Take the grey cover off, by turning it anti clockwise.Now, put the electrical connector back in place.TOP TIP: Your Ford Dealer can supply the bulb that’s right for your vehicle.Now remove the bulb through the connector.Squeeze both sides and pull the connector off. Fingerprints can shorten the life of the bulb. Screw the new bulb in clockwise to secure it.Turn the bulb anti-clockwise to remove it.Place the headlamp carefully on a flat, secure surface.TOP TIP: To protect your paintwork, ask someone to hold the headlamp for you.Now, the light will come completely away.At the back, there’s an electrical connector.Carefully pull the light up and off the white mounting point clip.TOP TIP: To avoid losing or dropping your tools, put them in the air vent tray by the windscreen.Next, undo the second screw at the front with your Torx screwdriver.Undo the screw with your Phillips screwdriver.This makes it easier to remove the screw. TOP TIP: Use your fingers to gently lift the surrounding plastic trim up.And make sure you secure it safely with the strut. This allows for the fan to stop working, too. For your safety, wait around 10 minutes for the engine to cool down.First, make sure your handbrake’s on and your ignition’s off.You’ll need a Ph2 Phillips screwdriver, too. A standard flat-head screwdriver will also work. How to change a headlight bulb? By the end of this short video, you’ll be able to do it like a pro.īefore you start, you’ll need a Torx Tx30 screwdriver. And in this step-by-step guide you’ll learn it. So, being able to change a bulb in your main beam, dip beam or indicator light is a valuable skill. If a bulb fails on your Ford, it’s more than just annoying: it can compromise your safety. Learn how to change a front light bulb like a professional. When you change the headlight on your RAV4, it is important to not touch the glass part of the bulb with your fingers because the oil from your fingertips will cause that part of the bulb to burn hotter, which significantly shortens the life of the bulb.Q: How many Ford drivers does it take to change a lightbulb? A: One. Toyota dealerships will tend to be pricier and parts retailers such as AutoZone will often replace it for free if you buy bulbs there. The headlight bulb replacement cost for your RAV4 varies depending on where you go to get your headlight replaced. If your RAV4 has a HID headlight burnt out, it could be a burnt out bulb or failed headlight ballast. Be sure to disconnect the headlight assembly or battery before attempting to replace it. Xenon headlights have a ballast to ignite the high voltage xenon lights when they turn on that can remain energized even if the lights are turned off. Some Toyotas have high intensity discharge headlights, sometimes referred to as xenon lights. In some Toyotas, the highbeam is the same bulb as the headlight and it is possible for the highbeam to work, but the headlight be burnt out even if they are the same bulb (and vice versa). Changing both headlight bulbs on your RAV4 at the same time will allow both bulbs to have the same intensity and prevent the new headlight bulb from appearing brighter than the bulb on the opposite side. Headlights grow dimmer by up to 20% over time and eventually burn out - for this reason, we recommend changing your headlights in pairs. This video shows you how to replace a headlight bulb in your 2010 Toyota RAV4, your headlight bulb may also be known as a headlight low beam.
0 Comments
Leave a Reply. |